[ 0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003dfe0000 (usable) [ 0.000000] BIOS-e820: 000000003dfe0000 - 000000003dfe3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003dfe3000 - 000000003dff0000 (ACPI data) [ 0.000000] BIOS-e820: 000000003dff0000 - 000000003e000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] 95MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f36a0 [ 0.000000] Entering add_active_range(0, 0, 253920) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 253920 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 253920 [ 0.000000] On node 0 totalpages: 253920 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 191 pages used for memmap [ 0.000000] HighMem zone: 24353 pages, LIFO batch:3 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP signature @ 0xC00F5980 checksum 0 [ 0.000000] ACPI: RSDP 000F5980, 0024 (r2 RS690 ) [ 0.000000] ACPI: RSDT 3DFE3000, 0034 (r1 RS690 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP 3DFE3080, 0074 (r1 RS690 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT 3DFE3100, 428C (r1 RS690 AWRDACPI 1000 MSFT 3000000) [ 0.000000] ACPI: FACS 3DFE0000, 0040 [ 0.000000] ACPI: _HPT 3DFE7440, 0038 (r1 RS690 AWRDACPI 42302E31 AWRD 98) [ 0.000000] ACPI: MCFG 3DFE7480, 003C (r1 RS690 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: APIC 3DFE73C0, 0068 (r1 RS690 AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DMI detected: Hewlett-Packard [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:12 APIC version 16 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3e000000:a2000000) [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251937 [ 0.000000] Kernel command line: boot=casper initrd=/casper/initrd.gz tz=Asia/Tokyo ramdisk_size=1048576 root=/dev/ram rw quiet splash BOOT_IMAGE=/casper/vmlinuz [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 997.535 MHz processor. [ 43.707623] Console: colour VGA+ 80x25 [ 43.707629] console [tty0] enabled [ 43.708158] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 43.708926] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 43.747619] Memory: 993892k/1015680k available (2157k kernel code, 21236k reserved, 998k data, 364k init, 98176k highmem) [ 43.747633] virtual kernel memory layout: [ 43.747635] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) [ 43.747638] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 43.747640] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 43.747642] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 43.747644] .init : 0xc041b000 - 0xc0476000 ( 364 kB) [ 43.747646] .data : 0xc031b5a4 - 0xc0414dc4 ( 998 kB) [ 43.747649] .text : 0xc0100000 - 0xc031b5a4 (2157 kB) [ 43.747654] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 43.747712] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 43.827701] Calibrating delay using timer specific routine.. 1997.10 BogoMIPS (lpj=3994204) [ 43.827746] Security Framework initialized [ 43.827755] SELinux: Disabled at boot. [ 43.827780] AppArmor: AppArmor initialized [ 43.827787] Failure registering capabilities with primary security module. [ 43.827801] Mount-cache hash table entries: 512 [ 43.827991] CPU: After generic identify, caps: 078bfbff ebd3fbff 00000000 00000000 00002001 00000000 00000119 00000000 [ 43.828008] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 43.828013] CPU: L2 Cache: 256K (64 bytes/line) [ 43.828018] CPU: After all inits, caps: 078bfbff ebd3fbff 00000000 00000410 00002001 00000000 00000119 00000000 [ 43.828036] Compat vDSO mapped to ffffe000. [ 43.828056] Checking 'hlt' instruction... OK. [ 43.844164] SMP alternatives: switching to UP code [ 43.846119] Freeing SMP alternatives: 11k freed [ 43.846320] Early unpacking initramfs... done [ 44.515991] ACPI: Core revision 20070126 [ 44.516096] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 44.520953] CPU0: AMD Mobile AMD Sempron(tm) Processor 2100+ stepping 02 [ 44.520987] Total of 1 processors activated (1997.10 BogoMIPS). [ 44.521302] ENABLING IO-APIC IRQs [ 44.521547] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 44.943265] Brought up 1 CPUs [ 44.943331] CPU0 attaching sched-domain: [ 44.943336] domain 0: span 01 [ 44.943339] groups: 01 [ 44.943620] net_namespace: 64 bytes [ 44.943631] Booting paravirtualized kernel on bare hardware [ 44.944420] Time: 10:36:07 Date: 09/01/09 [ 44.944459] NET: Registered protocol family 16 [ 44.944744] EISA bus registered [ 44.944768] ACPI: bus type pci registered [ 44.946659] PCI: PCI BIOS revision 3.00 entry at 0xfa300, last bus=3 [ 44.946663] PCI: Using configuration type 1 [ 44.946666] Setting up standard PCI resources [ 44.953193] ACPI: EC: Look up EC in DSDT [ 44.960142] ACPI: Interpreter enabled [ 44.960153] ACPI: (supports S0 S5) [ 44.960180] ACPI: Using IOAPIC for interrupt routing [ 44.967659] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 44.968918] PCI: Transparent bridge - 0000:00:14.4 [ 44.968955] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 44.969259] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [ 44.969418] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT] [ 44.969578] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] [ 45.002935] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.003130] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.003326] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.003512] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.003697] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.003883] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.004069] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.004255] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. [ 45.004449] Linux Plug and Play Support v0.97 (c) Adam Belay [ 45.004495] pnp: PnP ACPI init [ 45.004508] ACPI: bus type pnp registered [ 45.008241] pnp: PnP ACPI: found 11 devices [ 45.008246] ACPI: ACPI bus type pnp unregistered [ 45.008252] PnPBIOS: Disabled by ACPI PNP [ 45.008581] PCI: Using ACPI for IRQ routing [ 45.008585] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 45.107098] NET: Registered protocol family 8 [ 45.107103] NET: Registered protocol family 20 [ 45.107205] AppArmor: AppArmor Filesystem Enabled [ 45.111085] Time: tsc clocksource has been installed. [ 45.119140] system 00:01: ioport range 0x4100-0x411f has been reserved [ 45.119145] system 00:01: ioport range 0x228-0x22f has been reserved [ 45.119150] system 00:01: ioport range 0x40b-0x40b has been reserved [ 45.119155] system 00:01: ioport range 0x4d6-0x4d6 has been reserved [ 45.119160] system 00:01: ioport range 0xc00-0xc01 has been reserved [ 45.119164] system 00:01: ioport range 0xc14-0xc14 has been reserved [ 45.119169] system 00:01: ioport range 0xc50-0xc52 has been reserved [ 45.119174] system 00:01: ioport range 0xc6c-0xc6d has been reserved [ 45.119179] system 00:01: ioport range 0xc6f-0xc6f has been reserved [ 45.119184] system 00:01: ioport range 0xcd0-0xcd1 has been reserved [ 45.119189] system 00:01: ioport range 0xcd2-0xcd3 has been reserved [ 45.119193] system 00:01: ioport range 0xcd4-0xcdf has been reserved [ 45.119198] system 00:01: ioport range 0x4000-0x40fe has been reserved [ 45.119203] system 00:01: ioport range 0x4210-0x4217 has been reserved [ 45.119208] system 00:01: ioport range 0xb10-0xb1f has been reserved [ 45.119222] system 00:06: ioport range 0x4d0-0x4d1 has been reserved [ 45.119234] system 00:09: iomem range 0xe0000000-0xefffffff could not be reserved [ 45.119245] system 00:0a: iomem range 0xf0000-0xfffff could not be reserved [ 45.119250] system 00:0a: iomem range 0xfed00000-0xfed000ff could not be reserved [ 45.119255] system 00:0a: iomem range 0x3dfe0000-0x3dffffff could not be reserved [ 45.119261] system 00:0a: iomem range 0xffff0000-0xffffffff could not be reserved [ 45.119266] system 00:0a: iomem range 0x0-0x9ffff could not be reserved [ 45.119271] system 00:0a: iomem range 0x100000-0x3dfdffff could not be reserved [ 45.119276] system 00:0a: iomem range 0x3e000000-0x3fffffff has been reserved [ 45.119282] system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved [ 45.119287] system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved [ 45.119292] system 00:0a: iomem range 0xfff80000-0xfffeffff could not be reserved [ 45.149887] PCI: Bridge: 0000:00:01.0 [ 45.149892] IO window: e000-efff [ 45.149898] MEM window: fdc00000-fddfffff [ 45.149903] PREFETCH window: fa000000-fbffffff [ 45.149908] PCI: Bridge: 0000:00:04.0 [ 45.149911] IO window: d000-dfff [ 45.149916] MEM window: fdf00000-fdffffff [ 45.149920] PREFETCH window: fde00000-fdefffff [ 45.149924] PCI: Bridge: 0000:00:14.4 [ 45.149929] IO window: c000-cfff [ 45.149935] MEM window: fdb00000-fdbfffff [ 45.149941] PREFETCH window: fda00000-fdafffff [ 45.149974] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 45.149998] NET: Registered protocol family 2 [ 45.187175] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 45.187669] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 45.188871] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 45.189459] TCP: Hash tables configured (established 131072 bind 65536) [ 45.189465] TCP reno registered [ 45.199292] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0 [ 45.818626] it is [ 46.490603] Freeing initrd memory: 8388k freed [ 46.491517] audit: initializing netlink socket (disabled) [ 46.491536] audit(1251801368.368:1): initialized [ 46.491756] highmem bounce pool size: 64 pages [ 46.494588] VFS: Disk quotas dquot_6.5.1 [ 46.494701] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 46.494925] io scheduler noop registered [ 46.494929] io scheduler anticipatory registered [ 46.494932] io scheduler deadline registered [ 46.494951] io scheduler cfq registered (default) [ 46.634235] Boot video device is 0000:01:05.0 [ 46.634476] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 46.634506] assign_interrupt_mode Found MSI capability [ 46.634538] Allocate Port Service[0000:00:04.0:pcie00] [ 46.634856] isapnp: Scanning for PnP cards... [ 46.988883] isapnp: No Plug & Play device found [ 47.034930] Real Time Clock Driver v1.12ac [ 47.035068] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 47.035240] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 47.036159] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 47.037280] RAMDISK driver initialized: 16 RAM disks of 1048576K size 1024 blocksize [ 47.037383] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 47.037519] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 47.037523] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 47.038163] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 47.050040] mice: PS/2 mouse device common for all mice [ 47.050229] EISA: Probing bus 0 at eisa.0 [ 47.050254] Cannot allocate resource for EISA slot 4 [ 47.050277] EISA: Detected 0 cards. [ 47.050281] cpuidle: using governor ladder [ 47.050284] cpuidle: using governor menu [ 47.050421] NET: Registered protocol family 1 [ 47.050463] Using IPI No-Shortcut mode [ 47.050507] registered taskstats version 1 [ 47.050650] Magic number: 9:731:627 [ 47.050655] hash matches /build/buildd/linux-2.6.24/drivers/base/power/main.c:76 [ 47.050876] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 47.050880] EDD information not available. [ 47.051254] Freeing unused kernel memory: 364k freed [ 48.526313] fuse init (API version 7.9) [ 48.564322] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 48.564343] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 48.564361] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 48.566540] ACPI: Thermal Zone [THRM] (43 C) [ 49.127066] usbcore: registered new interface driver usbfs [ 49.127101] usbcore: registered new interface driver hub [ 49.148830] usbcore: registered new device driver usb [ 49.166178] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 49.166256] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 49.166279] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 49.166664] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 [ 49.166699] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02f000 [ 49.224907] usb usb1: configuration #1 chosen from 1 choice [ 49.224950] hub 1-0:1.0: USB hub found [ 49.224964] hub 1-0:1.0: 2 ports detected [ 49.328812] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17 [ 49.328836] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 49.328873] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 [ 49.328900] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02e000 [ 49.388807] usb usb2: configuration #1 chosen from 1 choice [ 49.388848] hub 2-0:1.0: USB hub found [ 49.388863] hub 2-0:1.0: 2 ports detected [ 49.492748] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 49.492773] ohci_hcd 0000:00:13.2: OHCI Host Controller [ 49.492815] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 49.492843] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02d000 [ 49.552740] usb usb3: configuration #1 chosen from 1 choice [ 49.552782] hub 3-0:1.0: USB hub found [ 49.552796] hub 3-0:1.0: 2 ports detected [ 49.656620] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17 [ 49.656644] ohci_hcd 0000:00:13.3: OHCI Host Controller [ 49.656683] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4 [ 49.656706] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02c000 [ 49.716640] usb usb4: configuration #1 chosen from 1 choice [ 49.716682] hub 4-0:1.0: USB hub found [ 49.716695] hub 4-0:1.0: 2 ports detected [ 49.804420] usb 2-1: new low speed USB device using ohci_hcd and address 2 [ 49.820547] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18 [ 49.820572] ohci_hcd 0000:00:13.4: OHCI Host Controller [ 49.820610] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5 [ 49.820632] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02b000 [ 49.880510] usb usb5: configuration #1 chosen from 1 choice [ 49.880552] hub 5-0:1.0: USB hub found [ 49.880565] hub 5-0:1.0: 2 ports detected [ 49.984465] tg3.c:v3.86 (November 9, 2007) [ 49.984492] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 49.984508] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 50.027124] eth0: Tigon3 [partno(BCM95787m) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:23:7d:11:39:57 [ 50.027138] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] [ 50.027143] eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 50.027221] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19 [ 50.027244] ehci_hcd 0000:00:13.5: EHCI Host Controller [ 50.027293] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6 [ 50.027349] ehci_hcd 0000:00:13.5: debug port 1 [ 50.027373] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe02a000 [ 50.029828] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 50.032858] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 50.034309] usb 2-1: unable to read config index 0 descriptor/start: -62 [ 50.034316] usb 2-1: chopping to 0 config(s) [ 50.036261] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 50.036482] usb usb6: configuration #1 chosen from 1 choice [ 50.036521] hub 6-0:1.0: USB hub found [ 50.036531] hub 6-0:1.0: 10 ports detected [ 50.038295] usb 2-1: string descriptor 0 read error: -62 [ 50.042313] usb 2-1: string descriptor 0 read error: -62 [ 50.042473] usb 2-1: no configuration chosen from 0 choices [ 50.140875] SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at PCI slot 0000:00:14.1 [ 50.140894] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 [ 50.140908] SB600_PATA: not 100% native mode: will probe irqs later [ 50.140921] ide0: BM-DMA at 0xfe00-0xfe07, BIOS settings: hda:DMA, hdb:pio [ 50.140937] Probing IDE interface ide0... [ 50.168242] usb 2-1: USB disconnect, address 2 [ 51.031703] usb 6-6: new high speed USB device using ehci_hcd and address 4 [ 51.100038] hda: 1GB ATA Flash Disk, ATA DISK drive [ 51.100092] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 51.100164] hda: UDMA/66 mode selected [ 51.100260] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 51.120061] SCSI subsystem initialized [ 51.137063] libata version 3.00 loaded. [ 51.166448] usb 6-6: configuration #1 chosen from 1 choice [ 51.475447] usb 2-1: new low speed USB device using ohci_hcd and address 3 [ 51.694535] usb 2-1: configuration #1 chosen from 1 choice [ 51.718576] hda: max request size: 128KiB [ 51.718584] hda: 2001888 sectors (1024 MB) w/1KiB Cache, CHS=1986/16/63 [ 51.718592] hda: cache flushes not supported [ 51.718641] hda: [ 52.007118] usb 2-2: new low speed USB device using ohci_hcd and address 4 [ 52.232905] usb 2-2: configuration #1 chosen from 1 choice [ 52.243064] usbcore: registered new interface driver libusual [ 52.243238] usbcore: registered new interface driver hiddev [ 52.251285] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:13.1/usb2/2-1/2-1:1.0/input/input1 [ 52.255104] input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:13.1-1 [ 52.256349] Initializing USB Mass Storage driver... [ 52.261414] input: CHICONY HP Basic USB Keyboard - JP as /devices/pci0000:00/0000:00:13.1/usb2/2-2/2-2:1.0/input/input2 [ 52.267627] scsi0 : SCSI emulation for USB Mass Storage devices [ 52.275052] input,hidraw1: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard - JP] on usb-0000:00:13.1-2 [ 52.275082] usbcore: registered new interface driver usbhid [ 52.275089] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 52.275588] usbcore: registered new interface driver usb-storage [ 52.275594] USB Mass Storage support registered. [ 52.275737] usb-storage: device found at 4 [ 52.275740] usb-storage: waiting for device to settle before scanning [ 57.272274] usb-storage: device scan complete [ 57.272779] scsi 0:0:0:0: Direct-Access USB_DRIVE 1.00 PQ: 0 ANSI: 2 [ 57.285046] Driver 'sd' needs updating - please use bus_type methods [ 57.286131] sd 0:0:0:0: [sda] 3991552 512-byte hardware sectors (2044 MB) [ 57.286779] sd 0:0:0:0: [sda] Write Protect is off [ 57.286785] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 57.286789] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 57.289369] sd 0:0:0:0: [sda] 3991552 512-byte hardware sectors (2044 MB) [ 57.289988] sd 0:0:0:0: [sda] Write Protect is off [ 57.289992] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 57.289996] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 57.290004] sda: sda1 [ 57.290728] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 57.301366] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 57.673685] Registering unionfs 1.4 [ 57.673692] unionfs: debugging is not enabled [ 57.694967] loop: module loaded [ 57.770589] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 76.746270] Linux agpgart interface v0.102 [ 76.860921] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 76.939642] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 77.345654] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device [ 78.404924] input: Power Button (FF) as /devices/virtual/input/input3 [ 78.419988] ACPI: Power Button (FF) [PWRF] [ 78.420143] input: Power Button (CM) as /devices/virtual/input/input4 [ 78.428000] ACPI: Power Button (CM) [PWRB] [ 79.115815] input: PC Speaker as /devices/platform/pcspkr/input/input5 [ 81.376255] udev: renamed network interface eth0 to eth1 [ 82.871008] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16 [ 86.107131] lp: driver loaded but no devices found [ 87.390013] ip_tables: (C) 2000-2006 Netfilter Core Team [ 88.384367] No dock devices found. [ 89.048105] powernow-k8: Power state transitions not supported [ 92.935776] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) [ 92.935785] apm: overridden by ACPI. [ 102.642779] hda-intel: Invalid position buffer, using LPIB read method instead. [ 120.473033] tg3: eth1: Link is up at 100 Mbps, full duplex. [ 120.473043] tg3: eth1: Flow control is on for TX and on for RX. [ 122.631307] NET: Registered protocol family 17 [ 537.666713] npviewer.bin[8845]: segfault at 00000028 eip b6fd1b72 esp bfdacac0 error 4 [ 559.008419] npviewer.bin[8853]: segfault at 00000028 eip b6f8bb72 esp bffef500 error 4